How to Remove a Stripped Screw From Laptop?

So, the question is “How to Remove a Stripped Screw From Laptop?” A classic and recurrent issue for most people is a screw connected to a motherboard with a striped or broken screw head! We were all here, taming a screwdriver to remove the screw only to find that it was destroyed, either by your impulsive behaviour or by a former handyman.

As the screw head is completely extended, the screwdriver cannot grasp and detach the screw. It is important to remember that individual laptop producers such as Apple use very particular screws (pentalobe, Torx, tri-wing), which are hard to find on the market. If you don’t have the right screwdriver, it’s best to go and buy one. Otherwise, you risk making things worse or even ruining your motherboard!

It takes a little imagination to remove a screw with a stripped head, but in the end, is very straightforward. We’ll go through a couple of different options. The tool you choose depends on your situation and what you have.

How to Remove a Stripped Screw From Laptop?

Laptops are also vulnerable to slashed screws. If you encounter one, use safe methods and avoid damaging strategies to prevent the expensive device’s adverse effects.

Therefore, many people have a concern about how they can remove striped torches safely and efficiently.

Here are a few ways to try on a laptop:

#1: Using an Elastic Band

Often what we need to eliminate is a little extra focus. An elastic belt’s rubber surface will help keep the screwdriver inside the broken cross and force any usable grip into it. Any rubber or elastic band, including the bicycle piece or the car tire hose, can do so as long as full contact is made between the head of the screw and the driver!

Read More: 10 Best Cheap Laptop for Music Production

Place the elastic on the bottom of the screwdriver and press enough to stick the flexible rubber to the screw under pressure. The rubber band helps to fill the places where the screw is corrupted and provides appropriate contact if the screw head is only slightly damaged.

#2: Try a Different Screwdriver

If your original screwdriver doesn’t work, different screwdrivers can be checked. You should first use one with smaller or larger heads. Then try a flat head screwdriver and see if the stripped screw is successful. If it doesn’t fit, you can also try a more powerful electric screwdriver.

#3: Using a Penetrating Oil Spray

Oil sprays like the WD-40 are conveniently available in your nearest hardware store. One of the most effective uses of the WD-40 is its ability to promote movement between rooms.

It has a solvent that attacks everything that blocks the screw and creates a thermal shock during application. Enable it to be on for at least 15 minutes, but the best results would be obtained if left to remain in the cold (about 40 F) or warm (about 85 F) setting overnight. You may do this by cooling it, for example, with ice cubes and heating a screwdriver’s shaft. As the temperature spreads through the screw, it slightly shrinks (cold) or expands (heat) and helps to “switch” further between the torque and the bracket.

Read More: How to Connect Ps4 to Laptop Without Remote Play

Just use the penetrating oil if you know that your screw is made of steel and there is no steel inside the motherboard! For this to work, the materials must be different. What could be easier than spraying a little WD-40 on the twin, ensuring it penetrates well between the support and the latter, waiting a few minutes, and attempting to disengage it. In most instances, this should be the trick. If not, then one of the more radical methods mentioned in this article must be taken.

#4: The Rubber Band Method

The next move is to use a thick rubber strip and your screwdriver. The technique is to place the rubber belt between the screw and the screwdriver.

The tension between the screwdriver and the screw is thus increased. Then apply appropriate pressure and turn the screwdriver slowly, before the screw moves.

Make sure the rubber band is large like your screw during this phase. So only a thicker rubber band and not the thin ones would fit. It also offers the handle you need to shift the screw.

#5: Using a Dremel

A much more damaging alternative is to make a slot on the screw head and turn it into a slotted screw. Although it is possible to use a hacksaw for the job, using a cutting disc or Dremel tool is more practical and useful.

The idea is to replicate a flat screwdriver indentation. To do this:

  1. Pick a thin bur (max 0.5 mm).
  2. Offer the impression that the cutter is so sharp as possible (not too deep around 1mm).
  3. Slowly but forcefully twist the image using a flat screwdriver.

#6: The use of screw-extracting pliers

You may use a pair of pinions to remove the screw if the head of the screw is available.

Place the pliers on the head of the screw and try to grasp them. Turn the pliers slowly and turn the screw with them, too. When the screw is loose, you can use your screwdriver to extract it.

If you don’t have a pair of screws, you can buy one from a hardware store. It is a handy tool, and it is essential to have electronic items such as laptops and phones periodically repaired.

#7: Using an Extractor

There is a final solution: nothing is known to the public, special “extractor” drills are available on the market. These are used in the same way as traditional drills, except that the boiling is conducted at a low speed in the opposite direction (unscrewing).

A screw extractor is a useful tool to remove the screw when it is broken. You can easily purchase a screw extractor from or online from your nearest hardware store. You should buy a screw extraction kit to ensure that any size screw can be extracted. You could then remove any missing screws: wooden screws, lagoon screws, plasterboard screws, metal screws, sheet metal screws, self-drilling screws, etc. You could then extract them. But most likely you have a stainless steel screw connected to your motherboard in this scenario.

Read More: How to Play Music From Phone to Laptop Windows 10

The extractor principle is simple and ingenious. As with the flexible system, the principle is that the head of the screw is “hung” as in ideal condition and the assembly is then screwed off. There is an inverted thread in the screw extractor that allows the screw to “screw” in the head as it turns in the direction of the assembly. The tool is typically found in various sizes to fit multiple sizes of screw heads. Once the right puller is located, it can be used on an electric screwdriver as a regular bit.

#8: The Superglue Method

If the above methods do not work, you may use superglue to remove the screw.

The approach is also very straightforward. Next, apply a little bit of super glue to the top of the screw. Put your screwdriver into the head of the screw and let the stick dry. Give the driver a turn to detach the screw with a sturdy handle.

After the screw has been removed, clean the superglue and the surrounding areas of the screw if it is present from the screwdriver’s tip.

#9: The Rotary Tool Method

If all of the above steps do not function, we have a rotary tool at the last stage. Put a thin cutting disk on the tool before starting the process to make sure it is locked in place. Wear your safe eyewear or girls to shield you from sparks or scratches.

Read More: 10 Best Cheap Laptop for Editing Youtube Videos

You are using the rotary tool to make a thin cut or groove in the head of the stripped screw when a low power setting is used. Then you can extract the screw with a flathead screwdriver.

Make sure the groove is sufficiently deep to match a flathead screwdriver. It should also be thin to be able to keep it securely for quick removal.

Video Guide:

FAQS (How to Remove a Stripped Screw From Laptop)

How do you remove a stripped bolt completely?

Most of the time, a chisel, a hammer drill, heat, and lubricant oil works. Heat expands and bolts, cracking the corrosive screen. The hammer box adds impact and torque to detach the bolt. Often hitting a chisel with a hammer will release the bolt.

How do you open a stuck screw on a laptop?

A rubber band will fill the holes and grip a screwdriver. Cut a rubber band, place it on the screw head flat & press the screwdriver on the screw and apply pressure to grip and twist the screw.

Why do my screw heads keep stripping?

Such items that trigger a screw to be removed include: Turning screws at an angle to the bolt using a screwdriver (or a drill)—using the wrong size screwdriver (especially one too small) Using the wrong size box bit, with power boiler.


This post looked at some ways to answer the common question: How to Remove a Stripped Screw From Laptop. No doubt, stretched screws will cause them a lot of misery and frustration.

There is, however, no need to worry because test methods and efficient tools for the effective removal of problem screws are available. The bottom line is that you are patient and careful about the steps.

We reiterate that if you’re not equipped with equipment or if you’re afraid you can’t do it properly, then your best to do it via an experienced laptop engineer.